Amphion BaseTWO25 Stereo Bass Extension System Stereo-Bass Erweiterungssystem, 2 Subwoofer Tower und 2x 900W Amp Modern music is increasingly bass-intensive. To pack the maximum amount of energy into the lowest octave – with no surprises in the playback – a sound engineer needs to hear and feel throughout the whole frequency spectrum. BaseTwo25 low-frequency extension system fits equally well in any composing, mixing, or mastering setup, where correct reproduction and appreciation of the lowest octave is critical. Amphion’s innovative approach to low-frequency monitoring provides producers, sound engineers and artists with a completely new perspective to the base. The BaseTwo25 is a state-of-the-art monitoring solution converting any Amphion two-way studio monitor into a full-range, time and phase coherent, three-way system. These full-range towers extend all the way down to 20Hz. Each BaseTwo25 has 2 x 25 cm woofers (top) and matching 2 x 25 cm radiators (below) mounted in back to back force-canceling mode on both sides of the cabinet. The system is driven by 2 x 900W amplifier, and controlled by Amphion’s signature filtering module with a variable-level attenuator. In addition to providing tight, tuneful bass, BaseTwo25 improves midrange clarity and increases the midrange power-handling abilities of the paired monitors. This is achieved by gradually transferring the low-end frequencies from the monitors to the base extenders. Features BaseTWO25: Perfectly integrated time and phase coherent, three-way system, extending all the way down to 20Hz Extremely robust 25 cm (10”) woofers with matching 25 cm passive radiators mounted in back to back force canceling mode on both sides of the cabinet3 Driven by 2 x 900W amplifiers housed in a 2U rack chassis and a stand-alone 1U filtering module with variable-volume control Specifications BaseTWO25: Operating principle: One-way, passive radiator Drivers: 10”aluminium woofers with 10″ passive radiators Crossover point: 100 Hz Frequency response: 20 – 100 Hz ±3dB Power rating: 2 x 900W RMS, 4 ΩW Weight: 70 kg (154 lbs) Handmade in Finland Specifications X-OVER: Dynamic range: 115 dB Mains: Input voltage 230/115V, autoselect Inputs: 2x Neutrik XLR inputs Speaker connectors: 3-way binding posts (banana, bare wire or spades) Casing: 19” rack mountable (2U) high quality aluminium Certification: CE, EuP and Energy Star Weight: 5,5 kg (12 lbs) Assembled in Finland Specifications AMP1000: Output power: 2 x 900 W RMS into 4 Ω @ 1% THD Frequency response: 10 Hz – 65 kHz (-3dB) Distortion: @1 W: 0,003% (100 Hz) @100 W: 0,006% (100 Hz) Dynamic range: 115dB Operating voltage range: 75 – 264 VAC Weight: 7 kg (15.5 lbs) Assembled in Finland

Amphion FLEXBASE25 Bass Extension System Stereo-Bass Erweiterung & Managementsystem, separater LFE Channel-Input und 600W Amp FlexBase25 -Lowest octave redesigned… Nailing the lowest octave-settings and translating it precisely from a studio to any listening situation is the foremost challenge for any contemporary music production. The fragmented playback environment demands extreme precision in the process of music creation and sound editing, especially when it comes to modern, bass-heavy production. A single mono subwoofer is part of a movie format, but Amphion does not believe it is good enough to be used in music production. In music, it is necessary to keep the stereo information throughout the whole frequency band. Amphion’s FlexBase25 presents you with an unconventional approach to subwoofer design that should fit especially well with the rapidly changing landscape of modern music-making and will satisfy even the most demanding producers or sound engineers. FlexBase is a single box, stereo subwoofer, which is placed in the centre line between the main speakers. Wide adjustment possibilities over crossover frequency (35-260 Hz), subwoofer level, as well as the mono-stereo spread, allow FlexBase to address the needs of a rapidly changing landscape of modern music-making. With a turn of a few dials, the system can be adapted to what best works for the project an engineer is working on. FlexBase can be fat, fun, and vibey when writing and producing. It will be precise, correct, and analytical when putting the finishing touches on a song or a film score. The system will allow you to continue to use your monitors for a narrower midrange view, as FlexBase can be bypassed. FlexBase works with all Amphion products. Pair it with One12, One15, Two15 or One18 for a smaller room full range system or place it with behind the console while keeping your One18, Two15 or Two18 on the meter bridge Features FLEXBASE25: Variable crossover frequency allows changing the flavour of the system to match the specifics of the various production tasks. Mono/stereo spread adjustment to ensure precise system-integration, even when higher crossover points are used. Fast and simple-to-set-up, easily adapting to a large variety of projects and acoustic environments. Specifications FLEXBASE25: Operating principle: One way closed box, stereo Drivers: 2 x 25 cm / 10” aluminium Crossover: Active 4th-order @ 35-260 Hz Max SPL: 117dB Frequency response: 20 Hz – 260 Hz +/-3dB (low pass) | 35 Hz – 200 kHz +/-3dB (high pass) Weight: 50 kg / 110 lb Handmade in Finland Specification FLEXAMP: Output power: 600W RMS into 4 Ω @ 1% THD Distortion: @ 1W: 0,003% (100 Hz) Distortion: @100W: 0,006% (100 Hz) Signal to noise ratio: 93dB @ 1W Efficiency: 85% @ full power (230V operation) Weight: 5 kg / 11 lb Assembled in Finland

Amphion Speaker cable (2x 5.0m) Cable for Amphion Speakers. Loudspeaker cable: 2×5.0 metre, specially braided silver coated copper conductor, terminated with Chord banana connectors. *Color might differ from picture, often Black Cables are supplied

Amphion AMP700 Endstufe - Endstufe für alle Amphion Lautsprecher - Amphion’s philosophy is to develop innovative products with high-performance and longevity. Amp700 delivers rock-solid control and tight, fast, high-resolving power to get maximum performance from your monitors. Amp700 provides 2 x 350 W for 8 ohm, and 2 x 700 W for 4 ohm load, which gives plenty of headroom for the highest level of performance. To reach the needed performance level, we developed a buffer-stage, which improved the sonics further by adding a subtle touch of class A sound to D class topology. Three step adjustment (0 dB, -12dB, -24dB) of the amplifiers input sensitivity allows finding suitable settings for each speaker model / application, which makes Amp700 a perfect partner to all Amphion models. Features Amphion Amp700: Power rating 2x 700W, 4Ω, 2x 350W, 8Ω Dynamic range 117 dB Certification CE, EuP and Energy Star Weight 5,5 kg (12 lbs) Mains Universal mains, auto select (100-240 V, 50-60 Hz) Inputs 2x Neutrik XLR inputs Speaker connectors 3-way binding posts (banana, bare wire or spades) Casing 19” rack mountable (2U) high quality aluminium